hydropool hot tub manuals
LINK 1 ENTER SITE >>> Download PDF
LINK 2 ENTER SITE >>> Download PDF
File Name:hydropool hot tub manuals.pdf
Size: 2919 KB
Type: PDF, ePub, eBook
Category: Book
Uploaded: 18 May 2019, 22:11 PM
Rating: 4.6/5 from 562 votes.
Status: AVAILABLE
Last checked: 4 Minutes ago!
In order to read or download hydropool hot tub manuals ebook, you need to create a FREE account.
eBook includes PDF, ePub and Kindle version
✔ Register a free 1 month Trial Account.
✔ Download as many books as you like (Personal use)
✔ Cancel the membership at any time if not satisfied.
✔ Join Over 80000 Happy Readers
hydropool hot tub manualsRecognized for quality worldwide, we are confident that your new hot tub will provide you, your family and friends, with years of enjoyment and fulfill all your hydrotherapy needs. If you don’t know your tolerance to hot water, or if you get a headache, or become dizzy or nauseous when using your hot tub, get out and cool off immediately. Simply compress the ends slightly, and slide into the semi-circular recess above the seat or lounger, with the Hydropool logo facing out. Although the pillows are designed to remain in-place in the hot tub, to extend the life of the pillows, remove after each use. WATERFALL If you received the optional waterfall package, remove the blade from the waterfall receiver fitting in the hot tub (already installed at the factory). Before any decking, tiling or carpeting is completed around the installation, fill and operate your hot tub to test for leaks (this ensures easy access and inexpensive correction). The automatically activate it for 30 seconds at the beginning of system will automatically turn off the blower each filter cycle. The following pads must be pressed within 3 seconds of each The system will automatically turn off the blower after other. Next, manually exit Before applying voltage to power-up your hot tub, it is very PRIMING MODE by pressing either the pad or the important that you understand the sequence of events that pad. Press to enter mode At this point PROGRAM, FILTER 1 and START TIME will appear on programming and press to select the desired mode. When the topside control panel lock is activated, all automatic functions will continue to operate The system will automatically turn off the mood lighting normally. All other the system to normal operation. MODE FUNCTION This key is used to change hot tub operation to SETTING SECOND FILTER CYCLE START TIME either ECONOMY or STANDARD mode. 1 Press Program key a fourth time.http://gartenstadt-apotheke.com/userfiles/98-mercury-mystique-repair-manual-download.xml
- Tags:
- hydropool hot tub controls, hydropool hot tub installation manual, hydropool serenity hot tub controls, hydropool hot tub manuals, hydropool hot tub manuals, hydropool hot tub manual.
INITIAL START-UP Before applying voltage to power-up your hot tub, it is very Once pump priming has been successfully completed, press important that you understand the sequence of events that pad and the pad to turn off the pumps. See DRAINING YOUR HOT TUB - p. 47 OPTIONAL for detailed instructions. The ozonator operates during FILTER CYCLES only. The display will show the O 3 icon while the ozonator is operating. When it hits. The waterfall feature was designed to provide a gentle cascade of water over the neck and shoulder area. Simply turn the top. The ideal range for hot tub water is 7.4 to 7.6 ppm. HOt tuB WAter CD.OzONATOR. Allow acrylic shell surface with a non-abrasive cleaner designed. If your hot tub is used daily or by a large number of bathers, the water should be drained more often. Otherwise, it will be necessary for your installer to add the extra supports where required. Spa control system is deactivated. At best, this is a temporary remedy, as excessive foam is merely a symptom of improper water balance. Manufactured by Hydropool Industries 335 Superior Blvd., Mississauga, Ontario, Canada L5T 2L6 Tel: (905) 565-6810 www.hydropoolhottubs.com. You can read more information on our cookies by reading our Privacy Policy. By continuing your journey on this site you consent to the continued use of cookies. R Milcarz, Edinburgh Whilst we make every effort to provide you the most accurate, up-to-date information, occasionally, one or more items on our web site may be mis-priced. AMA Connections Ltd FCA REGISTER No 816812 trading as Hydropool Scotland act as a credit broker and not the lender. Credit is provided by Hitachi Personal Finance, trading style of Hitachi Capital (UK) PLC, with whom we have a commercial relationship and we may receive a commission. Hitachi Capital (UK) PLC is authorised and regulated by the Financial Conduct Authority (Register no. 704348).http://solentpodiatry.com/jackvl940/web/content/images_uploaded/directsoft-quick-start-manual.xml Or, to learn how to select the perfect hot tub or swim spa, contact us for your free hot tub and swim spa buyer’s guides now. While there may be shipping delays, we are processing and shipping orders as quickly as possible.I've been curating spa and hot tub owner's manuals for many years, but now they sit dusty on the shelf, as most manufacturers have their owner's manuals listed online. Use these as guides for use, care and troubleshooting information. They also usually contain the spa warranty policy, in the appendix of the owner's manual. If you need help finding an owner's manual for your spa that is not listed here - it may not be available. Feel free to send us an email anyway - there is a small chance that we can find it, maybe sitting dusty on a shelf in my office. Hydropool hot tubs are not only healthful and relaxing, they can even add value to your home. Please take the time to carefully read and understand all the safety, installation and operating instructions in this manual before electrically connecting your hot tub and adding water. The following pages contain valuable information and pointers that will save you both time and money, as well as help you to simplify upkeep and maintenance. Since we manufactured our first hot tub in 1985, the Hydropool team has been dedicated to producing a quality product catering to maximum hydrotherapy, comfort, energy efficiency and ease of operation. We are confident that as you become more familiar with the various safety and maintenance features of your new hot tub you will be satisfied that you made the right decision in purchasing a Hydropool hot tub. Happy hot tubbing. David Jackson President 3 4 Save these instructions Important user safety instructions Your physiological response to hot water is subjective and depends on your age, health, and medical history.https://skazkina.com/ru/bosch-impactor-manual If you don t know your tolerance to hot water, or if you get a headache, or become dizzy or nauseous when using your hot tub, get out and cool off immediately. Always confirm water temperature with an accurate thermometer before entering your hot tub. 4 Do not allow children to submerge their head under water. 5 Do not use a hot tub unless all suction guards are installed to prevent body and hair entrapment. Where practical, install a safety grab bar or handrail. The causes, symptoms and effects of hyperthermia may be described as follows: Hyperthermia occurs when the internal temperature of the body reaches several degrees above the normal body temperature of 37 C (98.6 F). The symptoms of hyperthermia include drowsiness, lethargy, and an increase in the internal temperature of the body. The effects of hyperthermia include: Unawareness of impending hazard Failure to perceive heat Failure to recognize the need to exit the hot tub Physical inability to exit the hot tub Fetal damage in pregnant woman Unconsciousness resulting in the danger of drowning If you sense any of the symptoms of hyperthermia, safely exit the hot tub immediately. WARNING THE USE OF ALCOHOL, DRUGS OR MEDICATION CAN SIGNIFICANTLY INCREASE THE RISK OF FATAL HYPERTHERMIA. 4 5 CHOOSING THE RIGHT LOCATION Your Hydropool hot tub can be installed indoors or out, on the ground, in the ground or half-and-half. The following information will assist you in choosing the right location for your individual needs. When making your decision, always remember that hot tubs can be enjoyed year-round, indoors or out, regardless of the climate. Many Hydropool owners report that their favourite time to use a hot tub is in the cooler fall and winter months, while others praise the enjoyment of using their hot tub in the warmer spring and summer months.http://experience-hr.com/images/buderus-rc-20-manual.pdf INDOOR LOCATIONS If members of your family are not cold weather enthusiasts, or if your backyard or patio area is not suitable for a hot tub installation, then an indoor location for your hot tub may be your best or only choice. Indoor installations not only add a unique look and appeal to your home, they provide the privacy and controlled climate to ensure that use and enjoyment of your hot tub is maximized. If you are considering an indoor location, Hydropool manufactures certain lower profile models in two pieces (referred to as split models) that can be easily moved into most tight or difficult access locations and then assembled on-site by your authorized Hydropool dealer. These split and lower profile versions are designed to accommodate narrow doors or shallow stairwells. Since the dimension from the seat to the top of the lip is identical to the regular profile units, water submersion, for even the tallest user, is the same. Your Hydropool dealer can even arrange for your hot tub to be shipped without a cabinet or with the cabinet packaged separately for on-site installation. In many cases the smaller dimensions of a hot tub without a cabinet is all that is needed to ensure the hot tub can be delivered without wall or door alterations. Where the hot tub is being recessed, or a custom deck or tile is being installed, the cost savings of being able to order a hot tub without a cabinet is another benefit of choosing Hydropool. If you should choose an indoor location, you will find further information as outlined in the section SPECIAL CONSIDERATIONS FOR INDOOR INSTALLATIONS OUTDOOR LOCATIONS For a variety of reasons, outdoor locations are a far more popular choice. Some of the reasons include: Limited indoor space Delivery complications due to door openings, stairwells, etc.https://retentionstudentexperience.com/wp-content/plugins/formcraft/file-upload/server/content/files/16292c5af1bbe1---97-99-mitsubishi-eclipse-electrical-manual.pdf Limited budget (indoor installations usually also involve interior home renovations) Desire for an outdoor entertainment center Hot tub is being installed adjacent to an existing or planned swimming pool Concerns over splashing water inside the home For those who choose an outdoor location, hot tub operating temperatures can be adjusted to match the season. In colder months, many owners will operate their hot tub in the range of C ( F). During warmer months, an operating temperature of C (97-99 F) will provide a refreshing retreat. Please consider the following: a Your HYDROPOOL Hot Tub is self-supporting on its base. The cabinet should be decorative only, not for support. Never suspend the hot tub from the deck or cabinet.This will also provide greater overhead clearance for entry and exit to and from the hot tub It is beneficial to have the hot tub room located near wash room and shower facilities The hot tub room should have a floor drain to handle splash water, a window, outside exhaust fan or humidistat controlled exhaust fan for ventilation. You should not have concerns regarding humidity. When the hardcover is installed, no humidity will escape. During use, the small amount of humidity released into the room can be removed with the use of a dehumidifier Consider plumbing a water tap and drain location nearby to facilitate draining and top-up Always provide adequate ventilation for the support equipment Consult your local Hydropool retailer for further information SPECIAL CONSIDERATIONS 6 c Always provide adequate access for servicing the support equipment.The hot tub equipment and all electrical plugs, outlets and lights within 1.5m (5ft) of the hot tub must be G.F.C.I protected. Consult your electrician or local electrical authority for further details.cgalgeria-dubai.com/userfiles/files/canon-b150-user-manual.pdf Outdoor InstallationS Contact your local building code department to determine if a building permit is necessary and for information on applicable bylaws (distance from property lines, buildings, fencing requirements, etc.) If you are doing any excavating, contact your local gas, electric, and cable-company to ensure that there are no underground lines Locate the hot tub, where practical, within close distance of a door to the house to maximize potential winter use. Ensure that all hot tub support equipment is easily accessible and protected from the elements If possible, locate the hot tub where you will enjoy some privacy, out of the site of neighbours. If this is not possible, a partial privacy or wind partition, or proper placement of the optional Hydropool cover lifter should provide adequate privacy The hot tub support equipment is designed for indoor (out of the direct elements) use. When your HYDROPOOL hot tub is equipped with a factory-installed cabinet, and installed as per the guidelines of this manual, the equipment will be adequately protected. The potential drawback to this type of base is that splash water could eventually de-stabilize the ground under the base, with the resultant shift of the support base causing damage to the hot tub structure. Hydropool does not recommend back-filling full in-ground or partial in-ground installations. Difficult access can result in supplemental service labour charges not covered by the factory warranty. Consider easily removable deck materials. OVERALL SUPPORT Your Hydropool hot tub is equipped with a factory installed load support substructure, which distributes the weight of the water over the entire foot area of the hot tub. The cabinet, either factory installed or customized on-site, should be decorative only, and not relied on for overall support.https://bubblesoflove.net/wp-content/plugins/formcraft/file-upload/server/content/files/16292c5bb473a6---97-9064-manual.pdf Should you find that the support base is sloped or otherwise uneven, level your hot tub using TAPERED wood shims where necessary, ensuring that the tapered end extends at least 61 cm (24 in.) under the unit. This LEVELING YOUR HYDROPOOL HOT TUB will insure contact with the support substructure to appropriately distribute the weight of the unit. The standard Hydropool hot tub has the equipment installed inside the protective cedar cabinet. When your hot tub is to be installed above-ground, the cabinet is designed for both protection and accessibility When your hot tub is to be installed fully or partially in the ground, if you are relocating the equipment remotely from the hot tub, or if you have ordered a hot tub without a cabinet: it is necessary that the equipment is installed in an area that is dry, protected from the elements, has proper ventilation and is easily accessible for service Always ensure that the equipment is mounted on a raised base or platform to prevent potential water damage to the motor, equipment or controls Ensure that access to the equipment and the working area around the equipment is large enough to accommodate a service person remote EQUIPMENT Placement Whenever possible, install the pump(s) and control with heater below water level to ensure easy priming and maximize performance. Where above-grade equipment location is necessary, please ensure that your hot tub is equipped with the Remote Above-Grade Equipment Package. The equipment should be located as close to the hot tub as possible to maximize jet performance. Where you have ordered your hot tub with optional remote equipment, ensure that the equipment is not located more than 3 m. (10 ft.) from the hot tub. Use only 2 in. flex-pipe or larger for the pipe runs from the equipment to the hot tub, with minimal use of elbows or other pipe restrictions.https://www.reroofingbrisbaneqld.com.au/wp-content/plugins/formcraft/file-upload/server/content/files/16292c5c445923---970-extreme4-manual.pdf Install protective waterproof conduit to house applicable cords or line extensions such as the sensor and top-side control cables, light wires or ozone tubing. Each hot tub is factory strapped onto a wood skid. If your hot tub is to be delivered by your local dealer, it will generally arrive on a flat bed truck or low profile trailer. Most dealers are equipped with the necessary equipment to maneuver the hot tub from the truck to the dolly or cart that will be used to move your hot tub to the installation location. Should your hot tub arrive in a common closed box trailer, it may be necessary to arrange with a local towing company for a tilt and load tow truck, with a pulley winch system, to pull the skid from the larger trailer to the lower profile tow truck flat bed. The hot tub can be gently slid off the low profile trailer and positioned on its side on a cart or dolly. Most Hydropool models require a clearance width of at least 100 cm. (39 in.) to allow movement of the unit on its side through alley-ways, fence openings, etc. Where this is not possible, the use of a crane to lift the hot tub from the truck or trailer over the house to the patio or yard is often a simple and economical option. Do not move or place the hot tub on the side where the equipment is located as damage could occur Never roll or flip the hot tub end over end as the cabinet could be damaged Never lift or handle the hot tub by the plumbing Make sure that there is sufficient assistance to gently slide the hot tub off the dolly or cart to the support base without any damage Important Note: Damage caused during transportation or by improper handling is not covered by the factory warranty. 8 9 IMPORTANT ELECTRICAL SAFETY INSTRUCTIONS Safety comes first. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying the equipment.guyanapools.com/contents//files/canon-b150-manual.pdf 7 At least two lugs marked BONDING LUGS are provided on the external surface or on the inside of the supply terminal box or compartment. House Breaker Box (Neutral) To Hot Tub Support Equipment 11 12 PILLOWS Tubular Pillows The tubular pillows are a friction fit. Simply compress the ends slightly, and slide into the semi-circular recess above the seat or lounger, with the Hydropool logo facing out. ACCESSORIES Corner Wrap Pillows The corner wrap pillows are pre-installed at the factory and are attached via pin and socket. To remove, grasp ends of pillow and pull away from hot tub seat. To re-install, lineup pins on back of pillow to mounting sockets and press firmly. Waterfall Pillows If you received the optional waterfall package, remove the blade from the waterfall receiver fitting in the hot tub (already installed at the factory). Insert the waterfall blade through the front of the special waterfall pillow. The front flange of the waterfall blade will be recessed into the front of the pillow. If it is not recessed, the blade needs to be removed and re-inserted through the opposite side of the pillow. As the covers are identical to each other, simply place over either opening for a finished appearance. LED Mood lighting Press the light pad on the topside control to start the following LED lighting modes. When the LED lighting is turned off for more than 5 seconds, then turned back on, the system will resume the last light show. Description of Light Shows: Mode 1 Synchronous colour change Mode 2 Freeze mode, freezes on selected colour blend from above mode (gives unlimited colour blend selection) Mode 3 solid colour blue Mode 4 solid colour green Mode 5 solid colour red Mode 6 solid white (simulated) For systems with optional Galaxy light package: Mode 7 Galaxy lights OFF; interior lights ON Mode 8 Galaxy lights ON; interior lights OFF SAFETY HARDCOVER LOCKS The safety hard cover is designed to open away from the control area, however, if the hot tub is symmetrical in dimension, the cover can be oriented to open in either direction. WARNING Always ensure the safety hard cover is in place and locked whenever the hot tub is not being used. OPTIONAL COVER REMOVER Hydropool offers several different devices to assist in the removal of the safety hard cover. Please refer to the instructions supplied with your particular cover remover for installation. For further information, contact your local Hydropool retailer. 13 14 FILLING, CHECKING AND STARTING YOUR HOT TUB Checking Although your hot tub was thoroughly water-tested in the factory, some loosening of fittings can occur during shipping. Before any decking, tiling or carpeting is completed around the installation, fill and operate your hot tub to test for leaks (this ensures easy access and inexpensive correction). Check all union connections and plumbing for minor leaks. Unions Starting Before applying voltage to power-up your hot tub, it is very important that you understand the sequence of events that occur when the system is activated in order that the pump can be primed efficiently and damage to the system can be avoided. Gate Valves Hose Bib Turn the main power on at your electrical panel. Follow the control instructions for your particular model hot tub to put the pump into low speed. This mode will last for 4 to 5 minutes before automatically entering the normal operation mode. See complete details for your spa in section HYDROPOOL CONTROL SYSTEMS Proper Water Level Filling When adding water for the first time, the hot tub should be filled through the skimmer opening (helps to prevent air locks) using a standard garden hose, turning the tap on slowly to prevent damage to the surface by a jerking hose connection. Pull up the handles on the intake and return gate valves (handles are pulled up when valves are open and pushed down when valves are closed). Ensure the drain hose-bib is closed. Ensure that all jets are open. When the hot tub pump is located below water level, the water should start circulating immediately. If the motor works but you do not notice water circulation within the first 15 seconds, the pump may require priming due to trapped air (referred to as an air lock ). To prime, open the hose-bib to allow trapped air to escape. Close as soon as the water flow from the jets becomes regular. If the pumps have not primed after 2 minutes, and water is not flowing from the jets, DO NOT allow the pumps to continue to run. Turn power off at the main house panel (or GFCI) and try releasing the air again by loosening the union on the discharge side of the pump(s) while the motor is not running. Turn the power back on. If the pump(s) does not prime after 15 seconds, sometimes momentarily turning the pump(s) off and on will help the system to prime (note: do not do this more than 5 times). Important: Under NO circumstances should the pump(s) be allowed to operate without priming beyond 5 minutes, as this may not only cause unwarrantable damage to the pump, it may also cause the control system to go into an overheat condition. Definition: Priming a pump is a term used to describe the process in which air trapped in the plumbing and pump wet-end (referred to as an air lock ) is released, allowing the pump to move water efficiently through the plumbing system and to the jets. 14 15 RELEASING AIR TRAPPED IN FILTER. When the pump starts circulating on low speed, it will be necessary to release trapped air in the filter. Carefully loosen the vent valve counter-clockwise until there is the hissing sound of air escaping. Once there is a steady stream of water, close the vent valve, ensuring that the o-ring does not become pinched. Turn the pump onto high speed and re-check for leaks. The control system will automatically return the pump to low speed after 15 minutes. Adjust the hot tub heat control at the topside panel to the desired water temperature. Air Vent Valve Adjust water balance (ph, TA, calcium hardness) to recommended levels and add sanitizor. See section hot tub water maintenance The hot tub will require 8-10 hours to reach the desired temperature. Keep insulated safety hard cover on the hot tub, and the air controls closed during the entire heat up process. At initial power-up, this display will appear, and the system will show 4 sets of numbers in succession (ie. 100 then 104 then 28 then 240). These numbers represent the current software revision, and the system input voltage. After the initial software indicators are shown, this display will appear. This display is indicating that the system is in pump Priming Mode. This mode will last for 4 to 5 minutes before automatically exiting and entering the normal operation mode. You can also manually exit pump Priming Mode after the pump is primed. While in this mode, the heater circuit is disabled to allow the priming process to be completed without the possibility of energizing the heater element during low flow or no flow conditions. The system will not automatically activate any of the functions, however, by pushing the pad on the topside control, the pump can be manually activated to facilitate priming. Definition: Priming a pump is a term used to describe the process in which air trapped in the plumbing and pump wet-end (referred to as an air lock ) is released, allowing the pump to move water efficiently through the plumbing system and to the jets. PUMP PRIMING MODE As soon as PR is indicated on the topside panel, push the pad to start Pump 1 in low speed, then again to switch to high speed to facilitate priming. See FILLING, CHECKING AND STARTING YOUR HOT TUB for complete instructions on pump priming. Once pump priming has been successfully completed, press the pad to turn off the pump. Next, manually exit Priming Mode by pressing the pad. If you do not manually exit Priming Mode, it will automatically terminate after 4 to 5 minutes. Be sure that the pump is primed before exiting this mode. TEMPERATURE CONTROL FUNCTIONALITY AND ADJUSTMENT After you manually exit or the system automatically exits Priming Mode, your hot tub will automatically heat to the factory preset default temperature of 38 C (100 F) The topside panel will briefly show the default temperature, and then the display will appear as follows: Note that the water temperature is not yet displayed, as the system requires approximately 2 minutes of water flow through the heater to determine temperature. This is referred to as polling and is indicated on the display by the icon. After 2 minutes the display will show the current measured water temperature Press the pad to increase the temperature to the desired setting. The Heat indicator light on the Topside Panel will shimmer for 90 seconds, indicating that the system is not yet heating, then will illuminate solidly to indicate that the heater circuit has been energized and the spa water is being heated. In Standard Operating Mode, the system automatically activates Pump 1 low speed every 30 minutes for at least 2 minutes. After 2 minutes, the spa water temperature is determined. At this point, if the water temperature is lower than the set temperature, P1 will continue to run and the Heat indicator light on the Topside Panel will illuminate. The heater will operate until the water temperature reaches the set temperature point, after which, both the heater and Pump 1 low will automatically turn off. When this pad is pressed once any time during normal operation, the display will show the set temperature for 3 seconds. Press this pad a second time to increase or decrease the set temperature. To change the direction of the temperature settings (ie. lower vs. raise the temperature), allow the display to revert back to the current water temperature then press the pad again. Low speed starts automatically every 30 minutes to measure water temperature (in STANDARD Mode only see MODE FUNCTION), when a filter cycle is activated, or when a freeze condition is detected. When the blower (optional) is manually activated, the pump low speed is automatically activated and operates until the blower times out. If the blower is turned on even briefly, and then turned back off, low speed will operate for a minimum of 2 minutes. Next, press to configure the filter cycle frequency The display will show: both day and night cycles day cycle only night cycle only Press to select the filter cycle frequency For continuous filtration, select F12 and Press to exit programming mode and save changes. MODE FUNCTION A combination of keypads is used to change hot tub operation to either STANDARD, ECONOMY or SLEEP mode. PROGRAMMING Mode Function Press then - the current mode setting will flash on the display PUMP AUTOMATIC TIME-OUT High speed 15 minutes Low speed 4 hours Press Press to cycle though to the desired mode to select and confirm the selection. CLEAN-UP CYCLE The Clean-up Cycle begins 30 minutes after the pump or blower have been turned off or have automatically timed-out. The pump low speed and the ozonator (optional) will operate for one hour.