du1145xtpba manual
LINK 1 ENTER SITE >>> Download PDF
LINK 2 ENTER SITE >>> Download PDF
File Name:du1145xtpba manual.pdf
Size: 4928 KB
Type: PDF, ePub, eBook
Category: Book
Uploaded: 30 May 2019, 12:26 PM
Rating: 4.6/5 from 707 votes.
Status: AVAILABLE
Last checked: 8 Minutes ago!
In order to read or download du1145xtpba manual ebook, you need to create a FREE account.
eBook includes PDF, ePub and Kindle version
✔ Register a free 1 month Trial Account.
✔ Download as many books as you like (Personal use)
✔ Cancel the membership at any time if not satisfied.
✔ Join Over 80000 Happy Readers
du1145xtpba manualIf you want to search this text, hold control and F, and type the word you are looking for. Page: 1 INSTALLATION INSTRUCTIONS UNDERCOUNTER DISHWASHER PLASTIC GIANT TUB MODELS INSTRUCTIONS D'INSTALLATION LAVE - VAISSELLE ENCASTRA. Remove shipping materials, drain hose and lower rack. Close dishwasher door until latched.The dishwasher must be installed to meet all electrical and plumbing national and local codes and ordinances. 2 DISHWASHER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word a?? DANGER a?? or a?? WARNING. a?? These words mean: You can be killed or seriously injured if you don't immediately DANGER follow instructions.All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. WARNING Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. Page: 3 INSTALLATION REQUIREMENTS In addition, for first time installations Tools needed: Tools and Parts Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. All Installations Tools needed: Parts needed: Location Requirements Grounded electrical supply required.Motor should not touch the floor. Do not install dishwasher over carpeted flooring. Protect dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the warranty. A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry.http://eastsidemobileelectronics.com/userfiles/99-ranger-manual-locking-hubs.xml
- Tags:
- du1145xtpba manual, whirlpool du1145xtpba manual.
Parts supplied: A moisture barrier accessory ( Part No. 4396277 ) is available from your dealer for installing underneath the countertop, but is not required. Check location where dishwasher will be installed. The location must provide: a?? easy access to water, electricity and drain.Corner locations require a 2 a?? ( 5.1 cm ) minimum Make sure all these parts are included in the literature package.NOTE: To prevent shifting during dishwasher operation, shims must be securely attached to the floor. If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel. NOTE: Parts available for purchase in plumbing supply stores. Make sure pipes, wires and drain hose are within the Check local codes. Check existing electrical supply. See shaded area shown in the a?? Product and Cabinet a?? Electrical Requirements a?? section. It is recommended that Opening Dimensions a?? section. 3 electrical connections be made by a licensed electrical installer.National Fire Protection Association One Batterymarch Park a?? Make sure to connect drain hose to waste tee or disposer Quincy, MA 02269 inlet above drain trap in house plumbing and 20 a?? ( 50.8 cm ) minimum above the floor. It is recommended that You must have: the drain hose either be looped up and securely fastened a?? 120 - volt, 60 Hz, AC - only, 15 or 20 amp., fused electrical to the underside of the counter, or be connected to an supply. air gap. a?? copper wire only. We recommend: a?? a time - delay fuse or circuit breaker.If connecting dishwasher with a power supply cord: a?? Use UL listed power supply cord kit ( Part No. 4317824 ) marked for use with dishwasher.Outlet must meet all local codes and ordinances. If connecting dishwasher with direct wiring: a?? Use flexible, armored or non - metallic sheathed, copper wire with grounding wire that meets the wiring requirements for your home and a??http://forepic.com/_UploadFile/Images/99-r1-workshop-manual.xml Make sure to use an air gap if the drain hose is connected local codes and ordinances.Water Supply Requirements a?? A hot water line with 20 - 120 psi ( 138 - 862 kPa ) water pressure can be verified by a licensed plumber.See product and cabinet opening dimensions. 6 Check water and electrical 1 placement Water line ( 15.2 6 a?? cm ) Cable What type of electrical connection will you use. Power Supply Cord: Follow Option A instructions Direct Wire: Follow Option B instructions Do you already have utility 3 hookups. Yes a?? Follow instructions in the a?? Prepare Cabinet Opening a?? Existing Utilities a?? section. No a?? Follow instructions in the a?? Prepare Cabinet Opening a?? New Utilities a?? section. Existing utility hookups No existing utility hookups Water line Cable Shut off water supply 2 Shut off the water supply to the dishwasher. Disconnect power 1 Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. WARNING Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock.Tape cable to the floor in area shown. This will prevent Metal cabinet: Cover hole with grommet included with cable from moving when dishwasher is moved into power supply cord kit.See product and cabinet opening dimensions. Wood cabinet: Sand hole until smooth. Metal cabinet: Cover hole with grommet ( not provided ). Measure overall length of copper tubing or flexible braided water supply line. Attach to the hot water line using a connection configuration that is in compliance with local codes and ordinances. Tape drain hose to the floor in area shown. This will Slowly route water supply line through hole in cabinet.IMPORTANT: The drain hose connection of the disposer or a waste tee must be made before the drain trap and at least 20 a?? ( 50.8 cm ) above the floor where the dishwasher will be installed.http://eco-region31.ru/bose-ipod-speaker-manual Helpful Tip: To reduce vibration of the hose, keep the hose away from the floor. Option A, Waste disposer a?? no air gap Slowly turn water shutoff valve to a?? ON a?? position. Flush water into a shallow pan until clear to get rid of particles that could clog the inlet valve. Turn shutoff valve to a?? OFF a?? position. Install Drain Hose IMPORTANT: Always use a new drain hose. Check local codes to determine if an air gap is required. 1. Using a hammer and screwdriver, knock plug into disposer. 2. Use needle nose pliers to remove plug. 3. Attach drain hose to disposer inlet with large silver drain hose clamp ( provided ). Use pliers to squeeze clamp 2. Attach drain hose to air gap with large open and move into position. If the drain silver drain hose clamp ( provided ).Option C, Waste disposer a?? with air gap 3. Use a rubber hose ( not provided ) with screw - type clamps ( not provided ) to connect from waste tee to air gap. 1. Using a hammer and screwdriver, knock plug into disposer. 2. Use needle nose pliers to remove plug. 3. Connect black end of drain hose to air gap and cut if needed. ( Do not cut ribbed section. ) 4. Attach drain hose to air gap with large silver drain hose clamp ( provided ). Use pliers to squeeze clamp open and move into position. Wrap tape around coarse threads two to four times to prevent leaks. Using a wrench, tighten elbow until snug, and be sure that it faces to the rear. Helpful Tip: Place cardboard under dishwasher until installed in cabinet opening to avoid damaging floor covering. Do not use door panel as a work table without first covering with a towel to prevent scratching the door panel. Using two or more people, grasp sides of dishwasher door frame and place dishwasher on its back. Retain for later use. Do not remove tech sheet from access panel. 10 Remove panels 2 Put dishwasher on its back 1 WARNING Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door.http://hcberg.com/images/candy-dishwasher-cdi1012-instruction-manual.pdf Doing so can result in serious injury or cuts. WARNING Excessive Weight Hazard Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. Make sure screwheads are facing to the left when tightening conduit nut. Conduit connector may be provided with the power supply cord kit. Make Power Supply Cord Connection Option A, Power Supply Cord: Remove the green grounding screw and place through the ring terminal of the green ground wire. Reattach and tighten the green screw. Route cord so that it does not touch dishwasher motor to lower part of dishwasher tub. Pull cord through NOTE: Do not pre - twist stranded wire. Twist on wire conduit connector in terminal bow. connector. Gently tug on wires to be sure both are secured. Select UL listed or CSA approved twist - on wire connectors ( not included ) rated to connect your household wiring to Connect wires black to black and white to white, using 16 - gauge dishwasher wiring. UL listed or CSA approved twist - on wire connectors ( not included ). 11 Power Cord a?? Connect 3 remaining wires Power Supply Cord a?? 2 Connect ground wire Ground Ground wire wire Washer Ground connector WARNING Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Power Cord a?? Route cord 1 into terminal box Install conduit connector 6 What type of electrical connection will you use. Power Supply Cord: Follow Option A instructions Direct Wire: Follow Option B instructions Page: 12 Determine Cabinet Opening If needed, see website for animated representation of this step. Visit www.whirlpool.com under FAQ tab. Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed ( you will need to measure the lowest point on the underside of the countertop and the highest point on the floor ). Refer to a?? Dishwasher Height Adjustment Chart a?? for wheel position and the number of turns needed. Tighten conduit connector screws to secure cord. NOTE: If the minimum cabinet opening height is less than 34 a?? ( 86.4 cm ), the rear wheels can be removed for additional clearance. Insert tabs on left side Turn both leveler legs to the same height. Put wheels in of cover. Make sure wires are tucked inside box. Close the required position determined from a?? Dishwasher cover ensuring wires are not pinched.Add shims as needed in the door panel. Tilt dishwasher backwards on wheels and area shown to bring the dishwasher up to 34 a?? ( 86.4 cm ) move dishwasher close to cabinet opening.NOTE: Do not push on the front of the panel or on the NOTE: Shims must be securely attached to floor to console a?? they may dent. prevent movement when the dishwasher is in use. Helpful Tip: Temporarily tape utilities to the floor in the locations shown to prevent them from moving when Move Dishwasher into Cabinet dishwasher is moved into the cabinet opening. Opening Using two or more people, stand dishwasher upright. Check that water line is on the left side of opening and drain hose is near the center of the cabinet opening. NOTE: Do not install kickplate until instructed. With another person holding the dishwasher to prevent it from tipping, open and close the door a few times. Slowly move dishwasher completely into cabinet opening. Do not kink or pinch If the door closes too quickly, decrease the spring water line, drain hose, power supply cord or direct wire tension by moving the spring end toward the front of between dishwasher and cabinet. Remove cardboard the dishwasher.NOTE: Springs should be in the same notches on left NOTE: It is all right if dishwasher fits tightly into cabinet and right sides. opening. Do not remove insulation blanket a?? the blanket reduces the sound level. NOTE: If using power cord, make sure to route end through hole in cutout before sliding into cabinet opening. If the door falls open, increase the spring tension by moving the spring end toward the back of the Align front of dishwasher door panel with front of dishwasher.NOTE: Springs should be in the same notches on left and right sides. Check that leveling legs are firmly against the floor. Close and latch the door, and place level against the front panel. Check that dishwasher is centered from front to back in the opening. If needed, adjust leveling leg until dishwasher is plumb. Repeat for other side of dishwasher. 14 Check for plumb and 9 adjust legs if needed Align front of dishwasher 8 with front of cabinet doors Move dishwasher into 7 cabinet opening Insulation blanket Door falls open a?? 6 Increase spring tension Closes too quickly a?? 5 Decrease spring tension Page: 15 Helpful Tip: Push up on front of dishwasher to raise dishwasher off the ground to adjust front legs. Slide the nut and ferrule forward and start the nut onto the elbow threads. Place level against top front opening of tub. Check that dishwasher is level from side to side. If dishwasher is not level, adjust front legs up or down until dishwasher is level. Turn on water supply and check for leaks. If leak occurs, repeat NOTE: To prevent vibration during operation, route the previous step.Connect water supply 2 using copper or flexible line Check for leaks 4 Tighten copper or braided 3 tubing connection Slide nut and ferrule 1 onto tubing Nut Ferrule Check level side to side and 10 adjust legs if needed Preferred method Optional method Page: 16 Make Direct Wire Electrical Connect to Drain Connection NOTE: If the power supply cord was connected earlier proceed to Secure Dishwasher in Cabinet Opening section. Option B, Direct Wire: Place towel under drain hose to catch any water in drain hose. Place the small green drain hose clamp onto the small end of the drain hose. Push the new drain hose into the black drain hose connector up to the drain hose stop. Route cable so that it does not touch dishwasher motor or lower part of dishwasher tub. Pull cable through cable clamp in terminal box. Select UL listed or CSA approved twist - on wire connectors ( not included ) rated to connect your household wiring to 16 - gauge dishwasher wiring. Using pliers, squeeze open the small green drain hose clamp and slide onto connector between stops. Once connected, remove towel. Tighten conduit connector screws to secure cable. Form bare ground wire into a U - shaped hook. Wrap ground wire hook clockwise around ground connector screw and under the washer. Securely tighten ground connector. Place wires inside terminal box. Insert tabs on left side of cover. Make sure wires are tucked inside box. Close cover ensuring wires are not pinched. NOTE: Twist on UL listed or CSA approved wire connector. Gently tug on wires to be sure both are secured. Connect wires black to black and white to white, using UL listed or CSA approved twist - on wire connectors ( not included ). 17 Direct Wire a?? Reinstall 5 terminal box cover Direct Wire a?? Secure cable 4 in conduit connector Direct Wire a?? Connect 3 remaining wires Wiring configuration Terminal box wire: Power supply wire: white white black black ground connector ground wire Direct Wire a?? Connect 2 ground wire Ground Ground wire wire Washer Ground connector WARNING Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Page: 18 Secure Dishwasher in Cabinet Opening NOTE: Do not drop screws into bottom of dishwasher. The dishwasher must be secured to keep it from shifting when door is opened. Check that dishwasher is still level front to back and side to side in cabinet opening. IMPORTANT: If you have solid countertops such as corrian, granite, etc., you must use side mounting kit ( Part No. 8212560 ). Follow kit instructions. ( Brackets included with kit. ) Check that top of door does not contact screws, brackets, or countertop. If it does, adjust leveling legs. Open dishwasher door, remove lower dish rack, and place towel over pump assembly and lower spray arm of dishwasher. This will prevent screws from falling into pump area when securing dishwasher to countertop. Open door and check that space between dishwasher cabinet opening and tub is equal on both sides. If spacing is not equal, loosen bracket screws secured and shift tub. Tighten bracket screws. 18 Check inner spacing 5 Check door clearance 4 Secure dishwasher 3 Remove lower dish rack 2 and place towel Double check dishwasher 1 alignment in cabinet opening Page: 19 Hold the two panels together and place them against dishwasher leg. Complete Installation Check that the lower edge of the lower panel contacts the floor. Adjust if necessary. Check that grounding clip is attached to the lower panel. Position the lower panel behind the access panel. On some models there is insulation on the access panel which must fall behind the insulation on the lower panel. Tighten access panel screws. TEFLON is a registered trademark of E.I. Du Pont 19 De Nemours and Company. Tighten screws 4 Reinstall access panels 2 Check lower panel edge 3 Reinstall access panels 1 Insulation ( on some models ) Access panel Insulation Grounding clip Lower panel Remove towel and replace 6 lower dishwasher rack Page: 20 Check Operation Read the Dishwasher User Instructions that came a?? with your dishwasher. Check that all parts have been installed and no steps a?? were skipped. Check that you have all tools used. Start dishwasher and allow it to complete the shortest a?? wash cycle. After the first 2 minutes unlatch door, wait 5 seconds, then open door. Check to see that there is water in the bottom of the dishwasher tub. Check that dishwasher is working properly. If not, disconnect power or unplug dishwasher and see a?? If Dishwasher Does Not Operate a?? section. If Dishwasher Does Not Operate First try the solutions suggested here to possibly avoid the cost of a service call.If none of these work, call 1 - 800 - 253 - 1301, or in Canada, call 1 - 800 - 807 - 6777. For Roper models, call 1 - 800 - 447 - 6737, or in Canada call 1 - 800 - 807 - 6777. Additional Tips Expect longer wash times. Your new dishwasher will average 2 - 3 hours per load, but use nearly 40 less energy than older models. Designed with a low wattage, Plug into a grounded 3 prong outlet. Check that power low energy consumption motor, your dishwasher supply cord does not touch dishwasher motor or lower washes longer to ensure exceptional cleaning. Certain part of dishwasher tub.Reconnect Power Selecting certain options could increase cycle time past 3.5 hours. Rinse Aid is necessary for good drying results: This dishwasher is designed to be used with rinse aid for good drying performance and controlling hard water deposit build - up. Energy efficient dishwashers use less water and energy so they depend on the water sheeting action of rinse aid for good drying performance. Power supply cord a?? Plug into 1 a grounded 3 prong outlet WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Fermer la porte du lave - vaisselle, jusqu'A la position de verrouillage. Le non - respect de ces instructions peut causer des blessures graves ou des coupures. Consulter les codes locaux. Le moteur ne doit pas toucher le plancher. Ne pas installer le lave - vaisselle sur un plancher garni de tapis.Installer un tuyau de caoutchouc ( pas tuyau fournie ( argent ). Utiliser une pince pour ouvrir complA?tement la bride et la??enfiler sur le tuyau jusqu'A sa position finale.Le non - respect de ces instructions peut causer des blessures graves ou des coupures. Le non - respect de cette instruction peut causer une blessure au dos ou d'autre blessure.Fermer le couvercle - veiller A ne pas coincer des conducteurs. Faire intervenir deux personnes ou plus pour redresser le lave - vaisselle.Pour le raccordement des conducteurs ( conducteurs du cordon da??alimentation et conducteurs de calibre 16 du lave - vaisselle ) utiliser des connecteurs de fil ( homologation UL ou CSA ). Bien serrer la vis de connexion. Fermer le couvercle - veiller A ne pas coincer des conducteurs. REMARQUE: Installer chaque connecteur de fils sur les conducteurs ( mouvement de vissage ).Ne pas enlever la broche de liaison A la terre. Ne pas utiliser un adaptateur. Hold times are long. Screws sold seprately. Please see related items below. If the dishwasher isn't drying the dishes properly, the heating element may have burned out. Pouch contains 6 tablets. If the dishwasher does not drain then the drain hose could be clogged or the drain pump damaged or defective. Includes new strike for door latch. Look for tears, gaps or cuts in the gasket that could cause a dishwasher door leak. The stop clip prevents the dishrack from sliding all the way out of the dishwasher. The thermal fuse opens to cut off power to the dishwasher if the dishwasher overheats. If the thermal fuse fails, the dishwasher will not start. If the thermal fuse has failed, first investigate what caused the dishwasher to overheat. Per factory outside diameter is 1.42 inches. If original cap is bigger than that, may need to purchase entire dispenser assembly. The water inlet valve supplies water to the dishwasher. If the water inlet valve is defective, the dishwasher may not fill or may underfill. Since 1912, we've learned to recognize the most common problems.Do any of these look familiar. Join Repair Clinic's VIP email list for 10 off, plus other discounts and tips. We've got millions of parts, hundreds of brands, and thousands of step-by-step videos— everything you need to find it, fix it and finish the job right. Please try again in a bit.Please provide a US ZIP code.Use the button below to find your country's KitchenAid website.Your account allows you to track order history and provides for faster, easier purchasing and customer assistance. Once your account is created, you will be returned to checkout to complete your purchase. Link Example Your account allows you to track order history and provides for faster, easier purchasing and customer assistance. Once your account is created, you will be returned to checkout to complete your purchase. For more information about our privacy practices and a list of affiliated brands, please read out Privacy Notice.For more information about our privacy practices and a list of our affiliated brands, please read our Privacy Notice.Would you like to sign-in or create an account? Learn about our response to Covid-19 It takes 15-30 minutes to fix on average. The instructions below from DIYers like you make the repair simple and easy. So, if your DU1145XTPBA dishwasher dishes aren't getting clean, poor cleaning or won't clean dishes, the following info will help you identify the problem. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Includes impeller, shaft seal, volute and oring seal. Sump housing sold separate. For the complete circulation pump and motor assembly you must order with your model number.Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. Your appliance may differ depending on the manufacturer and model. If the temperature gets to high it will shut off the electrical current to the heating unit in the appliance. Also known as Thermal Fuse. The attaching solenoids on the valve open and close according to the desired amount of water needed. When it reaches a certain level, the float triggers this float switch to shut off, thereby shutting off the flow of water into the dishwasher. It is located on the bottom of the dishwasher and also comes with the 2 washers. Used with the heating element. They are sold individually. This valve allows the water to flow in the drain direction only and prevents the dirty water from coming back into the tub. The sump housing is sold separately. The sump housing is sold separately. The thermistor is part of the sensor mounted in the tub. The door strike serves as a mechanical actuator for door switch operation and provides door tension for proper seal. It glides over and under the the slide track. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element. Wheels are not included. They are sold individually. This part works like a little spray arm at the top of your dishwasher. Will not GU2500 XTP Built-in Dishwasher GU2500 XTP Built-in Dishwasher GU2500 XTP Built-in Dishwasher If I hit any button the light blinks but does not do anything. To turn off the lock Press and hold HEATED DRY for 4 seconds. The light turns off. Here is the manual: http: Check the wash cycle mode setting you have selected. Refer user manual. Two hrs cycle. DD-603SS Built-in Dishwasher Answer questions, earn points and help others. Model and serial numbers are located located inside the tub on a tag near the left side of the door opening:Once there, you will be givenThe site maintains the referenceUse of this Web site constitutes acceptance of the Terms of Service and Privacy Policy. Tested to complete. Unit is good to go.Unit is operating as designed.Removed fill tube to remove obstruction. Ice maker harvested and called for water. Yes to survey and leave behind.Ordering wheel. Will return to repair.; ordrng 1 WP697772 (blower wheel)Issues resolved. Unit tested properly. Survey prepped.; used 1 W11165546 (VALVE) from stockCustomer was also complaining about the water spout on the dispenser spraying water. I checked the leveling of the refrigerator and it was fine. Nothing was obstructing the drawer and it is installed properly. I called Tech-Line and spoke with Kevin. We decided to change out the pantry adapters and change out the spout. However the spout was not easy to identify. I ordered all related parts and will return to vendor what is not needed.; ordrng 1 W10403752 (switch) and 1 W10654548 (ASSEMBLY SEPARATOR) and 1 W10654549 (WALL DISPENSER FALSE) and 1 W11106553 (ASSEMBLY USER INTERFACE BLACK) and 1 W11294509 (ADAPTER PANTRY LEFT HAND) and 1 W11294512 (ADAPTER PANTRY RIGHT HAND) and 1 W11294548 (ASSEMBLY PANTRY CENTER ADAPTER)I checked temperature and it was at 58 degrees F. The called Whirlpool and told them they would fix it. I ran diagnostics and all components were working. No error codes. Compressor was hot. And there is a fan for both the compressor and evaporator. There was no frost build up on condenser and it was not cold. Called SG. He instructed me to order a compressor and a sealed system tech. I ordered part.; ordrng 1 W11034254 (compressor)Unit is working properly. Job complete.Found frozen evap. defrost evap. No other issue job completeReplace water valve and filter housing. Unit now dispensing water without noise. No other issues job complete.Finding switch is sending proper voltage. Ohmed blower motor per tech sheet and finding blower motor to be the issue. Calling techline to see if this is a known issue and if need to order “fresh stock”. Spoke with Andy. He stated to order from Plainfield.