docuprint c1110 manual
LINK 1 ENTER SITE >>> Download PDF
LINK 2 ENTER SITE >>> Download PDF
File Name:docuprint c1110 manual.pdf
Size: 3043 KB
Type: PDF, ePub, eBook
Category: Book
Uploaded: 26 May 2019, 20:41 PM
Rating: 4.6/5 from 620 votes.
Status: AVAILABLE
Last checked: 4 Minutes ago!
In order to read or download docuprint c1110 manual ebook, you need to create a FREE account.
eBook includes PDF, ePub and Kindle version
✔ Register a free 1 month Trial Account.
✔ Download as many books as you like (Personal use)
✔ Cancel the membership at any time if not satisfied.
✔ Join Over 80000 Happy Readers
docuprint c1110 manualInstall a drum cartridge appropriate for the printer. Install the X toner cartridge appropriate for the printer. This message may appear when the accessory configuration settings differ from the actual configuration. Cancel the job by pressing the button on the control panel. Correctly specify the print request and try printing again. For information about the Print Auditron, consult your system administrator. Load Manual Feeder XXXXXXXX Load Manual Feeder YYYYYYYY The paper is not loaded in the manual feeder. Load paper of the size (XXXXXXXX) and type (YYYYYYYY) indicated in the message in the manual feeder. If printing the job, press the button. If cancelling the job, press the button. Or, when you requested the job, you did not correctly enter your user ID and password on your print driver. Enter the correct user ID and password and try printing again. Consult your system administrator whether you have access to the printer. Stack the prints and turn the stack over. One sheet at a time, insert the very top print that was turned over with the blank side facing down, into the manual feeder. Press the button to start printing. Download FujiXerox C1110 Service Manual.PRINTED IN JAPAN Company Name Department Name Telephone No. Full Name Employee No. Introduction Getting to know the Service Manual How to use the Service Manual Terms and Symbols Abbreviations Chapter 1 Service Call Procedure Chapter 2 Troubleshooting Chapter 3 Image Quality Troubleshooting Chapter 4 Repairs and Adjustments Chapter 5 Parts List Chapter 6 General Chapter 7 Wiring Data Chapter 8 Accessories Chapter 9 BSD (Block Schematic Diagram) Not yet issued Chapter 10 Machine Overview Preface Preface Table of Contents Table of Contents 1 Getting to know the Service Manual. Preface-1 2 How to use the Service Manual. Preface-1 2.1 2.2 Contents of Manual.Preface-1 Information on Updating.Preface-2 3 Terms and Symbols. Preface-3 4 Abbreviations.http://www.adbagroup.com/E/canadian-solar-module-installation-manual.xml
- Tags:
- docuprint c1110 manual, docuprint c1110 manual, docuprint c1110 manual pdf, docuprint c1110 manual download, docuprint c1110 manuals, docuprint c1110 manual free.
Chapters This manual is divided into ten chapters as described below. Revisions must be incorporated correctly to keep the manual up-to-date. Revision Sidebar When any paragraph, table or figure has been added or amended, a revision sidebar will be added to indicate where the revision was made. (Example) If the same page is changed again due to a subsequent revision, revision sidebars associated with the previous revision(s) will be deleted. Preface-2 Introduction 3. Terms and Symbols 3. Terms and Symbols Specific terms and symbols used in any particular chapter are described in the Preface for that section. WARNING Indicates a potentially hazardous situation, such as death or serious injury if operators do not handle the machine correctly by disregarding the statement. CAUTION Indicates a potentially hazardous situation, such as injury or property damage if operators do not handle the machine correctly by disregarding the statement. INSTRUCTION Indicates that the printer or its components may be damaged if the instructed procedure is not strictly observed. NOTE Used to emphasize the procedure, servicing, and regulation. REFERENCE Used to describe the technical terminology and supplementary explanations. Indicates the adjustment procedure for reference. Indicates the parts list for reference. Means Assembly. Safety Critical Components (SCC) Control of the safety of components that are designated Safety Critical Components shall conform to Fuji Xerox Co. Ltd-stipulated rules and regulations on Safety Critical Components. Important Information Stored Component (ISC) Important Information Stored Components store customers’ important information they have entered after machine installation. When replacing Important Information Stored Components, you must replace and discard them, following the procedure described in Chapter 4 Adjustments. Take care never to let customer information leak out.http://diagcorlifescience.com/attachment/canalyzer-manual-pdf.xml Registration RH Right Hand ROS Raster Output Scanner ROT Rotary RTC Rubber Tube Charger RTN Return SEF Short Edge Feed SG Signal Ground SMH Special Material Handler SNR Sensor SOL. Solenoid SOS Start Of Scan STM Single Tray Module SW Switch TEMP. Do not perform any hazardous operation. 1. Power Supply To prevent electrical shocks, burns, or injury, etc., be sure to switch OFF the machine and disconnect the plug before starting the maintenance servicing. If the machine has to be switched ON, such as when measuring the voltage, take extra care to prevent an electrical shock. 2. Drive Area Never inspect or lubricate the drive area such as the gears during the machine operation. 3. Heavy Parts The weight of the machine is 18kg. When moving the machine to ensure sufficient working space, take extra care to prevent back pain. 4. Safety Device See that safety devices for preventing mechanical accidents, such as fuses, circuit breakers, interlock switches, etc., and those for protecting customers from injury, such as panels and covers, function properly. Modifications that hinder the function of any safety devices are strictly prohibited. 5. Installing and removing the parts The edge of parts and covers may be sharp, take care not to touch them. If the oil gets onto your hand, wipe it off before getting on with the servicing. When using a cleaner to clean the remaining toner, be sure to use the FX standard toner-proof cleaner and not a customer's cleaner. NOTE For the separation and processing methods for the collected items, refer to the Common Technical Information No. 2-138 for all machines. Always have 2 people available to move the printer. Refer to the Installation Procedures for details. 1-3 Chapter 1 Service Call Procedure 1.2 Servicing Call Procedure 1.2 Servicing Call Procedure Initial Actions 1. 2. 3. 4. Ask the operator(s) about the machine condition. Record the billing meter readings. Inspect any printing error, then check the machine. Check the Service Log. 1.http://ninethreefox.com/?q=node/11290 2. 3. 4. UM Call Troubleshoot on Level 1. Troubleshoot. Check the print quality using the test patterns on the machine. Feed paper from the respective trays and, if necessary, clean or replace the Feed Roll. 5. Repair all the secondary problems. 6. Perform TRIM servicing. SM Call 1. Check the print quality using the test patterns on the machine. 2. Feed paper from the respective trays and, if necessary, clean or replace the Feed Roll. 3. Repair all the secondary problems. 4. Perform TRIM servicing. Check the machine exterior and consumables. Train the operator as required. Complete the Service Log and Service Report. This items are not registered as spare part. 1-6 Chapter 1 Service Call Procedure 1.3 TRIM Servicing 1.3.3 TRIM Check List A ------ Perform checking. Clean, replace or supply if necessary. B ------ Always perform cleaning and checking. If the printer is kept ON, never touch the conductive parts while it is not specifically required. The power switch and inlet are live even while the power supply is cut off. When checking some parts with covers removed and with the interlock and safety and power switches ON, laser beams may be irradiated from the ROS ASSY. When checking some parts with the Front Cover removed and power ON, high voltage may be applied by the PWBA HVPS. When using Diag. Tool or other tools of high voltage, never touch parts of high voltage. When using Diag. Tool or other tools of high voltage, be sure to follow the procedures in this manual. 2-2 Chapter 2 Troubleshooting 2.1 Progressing with the Troubleshooting 5 When operating the driving units using the Diag or other tools, be sure to keep them covered unless otherwise specified. When operating the driving units using the Diag or other tools, never touch the driving units. When operating the driving units using Diag or other tools, be sure to follow the procedures in this manual. 6 When touching hot parts, be careful not to get burnt.http://cleananddecluttered.com/images/brunswick-bowling-service-manual.pdf 7 Workers should wear a wrist band or the like to prevent static electricity from their body, grounding their body while working. 2.1.4 Cautions for FIP Use 1 When troubleshooting according to the FIP, normal PWBA MCU, PWBA HVPS, PWBA LVPS, FUSER ASSY, TRANSFER ASSY and so no may be necessary for isolation of failed parts. Handle the tool with care, as the leading edge of the tool is pointed. 10 When measuring the voltage, set the TRANSFER ASSY, TONER CARTRIDGEs and Paper Cassette, close the COVERs and power ON if not required specifically. 11 Numerical values in the FIP are only for standard. If numerical values are approximate, they should be considered permissible. 2-3 Chapter 2 Troubleshooting 2.1 Progressing with the Troubleshooting 12 Parts which are always removed to check as indicated in the FIP and procedures for that purpose are not specifically referred to here. Correct troubles according to the instructions in the FIP. 15 For optional parts, some troubleshooting procedure may follow the manual for those options, of which you should take note. Keep those manuals for the optional parts when required. 2.1.5 Items to Be Confirmed Before Going to FIP Troubleshooting 2.1.5.1 Basic Printer Problems Some printer problems can be easy to resolve.In the detailed error display mode, detailed error status can be displayed on your PC.Determine the host interface you are using. Print a Panel Setting page to verify that the current interfaces settings are correct. 8 Output fonts will not print correctly using the PCL driver in its default mode. To correct this problem, use PostScript driver when using the PCL driver.Decrease this number.Refer to Print Media Guidelines of this section. 2 Flex print media before loading it. 3 Make sure the print media is loaded correctly. 4 Make sure the width and length guides on the print media sources are adjusted correctly. 5 If the print media are overfilled in sources, reduce the amount of media.http://churchliferesources.org/wp-content/plugins/formcraft/file-upload/server/content/files/16290dbd5dd6c3---04-f150-manual-pdf.pdf 6 Load the recommended print side correctly for the type of print media you are using. 7 Turn the print media over or around and try printing again to see if feeding improves. 8 Check the print media type loaded in the source, and refill only one type of print media, if print media types are mixed. 9 Refill a new ream of print media, if some reams are mixed. 10 Remove the top and bottom sheets of a ream before loading the print media. 11 Load a print media source only when it is empty.Your printer provides high-quality printing on a variety of print media. Selecting the appropriate print media for your printer helps avoid printing troubles. This section describes how to select print media, how to care for print media, and how to load the print media in the standard 250sheet tray module. Before buying large quantities of any print media, it recommends trying a sample first. When loading paper, identify the recommended print side on the paper package, and load the paper accordingly. Paper Characteristics The following paper characteristics affect print quality and reliability. It recommends that you follow these guidelines when evaluating new paper stock.Curl Curl is the tendency of print media to curve at its edges. Excessive curl can cause paper feeding problems. Curl usually occurs after the paper passes through the printer, where it is exposed to high temperatures. Storing paper unwrapped in humid conditions, even in the paper tray, can contribute to paper curling prior to printing and cause feeding problems. Smoothness The degree of paper smoothness directly affects print quality. If the paper is too rough, the toner does not fuse to the paper properly, resulting in poor print quality. If the paper is too smooth, it can cause paper feeding problems. 2-6 Chapter 2 Troubleshooting 2.1 Progressing with the Troubleshooting Moisture Content The amount of moisture in the paper affects both print quality and the ability of the printer to feed the paper properly.AYHANCEVIK.COM/images_upload/files/canon-l140-fax-manual.pdf Leave the paper in its original packaging until you are ready to use it. This limits the exposure of the paper to moisture changes that can degrade its performance. Grain Direction Grain refers to the alignment of the paper fibers in a sheet of paper. Grain is either grain long, running the length of the paper, or grain short, running the width of the paper.Fiber Content Most high-quality xerographic paper is made from 100 chemically pulped wood. Paper containing fibers such as cotton possess characteristics that can result in degraded paper handling. Always print several samples before buying large quantities of any type of print media. When choosing any print media, you should consider the weight, fiber content, and color. Only use paper able to withstand these temperatures without discoloring, bleeding, or releasing hazardous emissions. Check with the manufacturer or vendor to determine whether the paper you have chosen is acceptable for laser printers. To help avoid jams or poor print quality: 1 Always use a new, undamaged paper. 2 Before loading the paper, identify the recommended print side of the paper. This information is usually indicated on the paper package. 3 Do not use paper that you have cut or trimmed yourself. 4 Do not mix print media sizes, weights, or types in the same source. This may result in a paper jam. 5 Do not remove trays while a job is printing. 6 Make sure the Paper Type and Paper Size settings are correct. 7 Make sure the paper is properly loaded in the tray. 8 Flex paper back and forth, and then fan them. The FIP isolates the presence of various troubles including error codes, and guides the troubleshooting procedure. 2.2.2 Flow of FIP Ask the operator about trouble status. Is operator's operating method correct. N Y Instruct how to operate Turn off and turn on the Power. Does error still occur when print is done by the problem mode.https://brothersaluminium.com.np/wp-content/plugins/formcraft/file-upload/server/content/files/16290dbeb2df5f---04-ford-crown-victoria-owners-manual.pdf Error Restart Printer System Flip Error 024-371 Restart Printer Invalid User Press Ok Button Flip Error 016-757 Press Ok Button Disabled Func Press Ok Button Flip Error 016-758 Press Ok Button Limit Exceeded Press Ok Button Flip Error 016-759 Press Ok Button Error Contents Relevant FIP ROS Failure is detected. Go to step 3. Disconnect and reconnect the USB or network cable. Does the error still occur when the power is turned OFF and ON. End of work 3 Checking after reseating the PWBA ESS Reseat the PWBA ESS. Go to step 4. End of work 4 Checking re-downloading the correct file for 6130N Re-download the correct file from Xerox web site. Replace the PWBA ESS. (Refer to REP8.3) End of work Go to step 2. 2-23 Re-download the correct file. Chapter 2 Troubleshooting 2.3 ERROR CODE FIP FIP-1.2 Step Out of Memory 016-718 Remedy Check Yes No Possible causative parts: PWBA ESS (PL8.1.9) MEMORY CARD (OPTION) (PL8.1.12) 1 Checking the memory capacity for print Print the small size file (like a Windows test print). Does the error still occur when printing. Go to step 2. Add the MEMORY CARD or divide the printing job. 2 Checking after reseating the MEMORY CARD Reseat the MEMORY CARD. Go to step 3. End of work 3 Checking the memory card capacity Is the memory capacity recognized normally. Go to step 4. Replace the PWBA ESS. (Refer to REP8.3) 4 Checking after replacing the MEMORY CARD Replace the MEMORY CARD. Replace the PWBA ESS. (Refer to REP8.3) End of work 2-24 Chapter 2 Troubleshooting 2.3 ERROR CODE FIP FIP-1.3 PDL Error 016-720 Step Remedy Check Yes No Possible causative parts: PWBA ESS (PL8.1.9) 1 Checking the printing job Print the small size file (like a Windows test print). Go to step 2. End of work 2 Checking after reseating the PWBA ESS Reseat the PWBA ESS. Replace the PWBA ESS. (Refer to REP8.3) End of work 2-26 Chapter 2 Troubleshooting 2.3 ERROR CODE FIP FIP-1.5 PAGEC Time Error 024-362 Step Remedy Check Yes No Possible causative parts: PWBA ESS (PL8.1.https://snookerfootball.eu/wp-content/plugins/formcraft/file-upload/server/content/files/16290dc0074a72---04-f250-service-manual.pdf9) 1 Checking the error Does the error still occur when turning off and on the power. Go to step 2. End of work, if the error occurs again, go to step 2. 2 Checking the PWBA ESS installation Reseat the PWBA ESS. (Refer to REP8.3) Does the error still occur when turning off and on the power. Replace the PWBA ESS. Does the error still occur when the power is turned ON. Go to step 2. End of work 2 Checking after replacing the MEMORY CARD Replace the MEMORY CARD. Go to step 4. End of work 4 Checking the HARN ASSY TONER CRUM for continuity Disconnect J31 from the PWBA MCU. Disconnect J311 (Y), J312 (M), J313 (C) or J324 (K) from the connector CRUM. Is each cable of J31 J311, J312, J313 or J324 continuous. Go to step 5. Replace the HARN ASSY TONER CRUM 5 Checking after reseating the PWBA MCU Reseat the PWBA MCU. (Refer to REP8.11) Does the error still occur when the power is turned OFF and ON. Go to step 2. End of work 2 Checking the Toner Type Is the Xerox Toner seated. Go to step 3. Replace the TONER CARTRIDGE (Y). 3 Checking after reseating the TONER CARTRIDGE (Y) Reseat the TONER CARTRIDGE (Y), and check that the lock key is in the lock position. Go to step 4. End of work 4 Checking after replacing the TONER CARTRIDGE (Y) Replace the TONER CARTRIDGE (Y), and check that the lock key is in the lock position. Go to step 7. End of work 7 Checking the HARN ASSY TONER CRUM for continuity Disconnect J31 from the PWBA MCU. Disconnect J311 from the CONNECTOR CRUM. Is each cable of J31 J311 continuous. Go to step 8. Replace the HARN ASSY TONER CRUM. 8 Checking the power to CONNECTOR CRUM Disconnect J31 from the PWBA MCU. Go to step 3. Replace the TONER CARTRIDGE (M). 3 Checking after reseating the TONER CARTRIDGE (M) Reseat the TONER CARTRIDGE (M), and check that the lock key is in the lock position. Go to step 4. End of work 4 Checking after replacing the TONER CARTRIDGE (M) Replace the TONER CARTRIDGE (M), and check that the lock key is in the lock position.AYBAR-GALLERY.COM/userfiles/files/canon-l140-fax-machine-user-manual.pdf Disconnect J312 from the CONNECTOR CRUM. Is each cable of J31 J312 continuous. Go to step 3. Replace the TONER CARTRIDGE (C). 3 Checking after reseating the TONER CARTRIDGE (C) Reseat the TONER CARTRIDGE (C), and check that the lock key is in the lock position. Go to step 4. End of work 4 Checking after replacing the TONER CARTRIDGE (C) Replace the TONER CARTRIDGE (C), and check that the lock key is in the lock position. Disconnect J313 from the CONNECTOR CRUM. Is each cable of J31 J313 continuous. Go to step 3. Replace the TONER CARTRIDGE (B). 3 Checking after reseating the TONER CARTRIDGE (K) Reseat the TONER CARTRIDGE (K), and check that the lock key is in the lock position. Go to step 4. End of work 4 Checking after replacing the TONER CARTRIDGE (K) Replace the TONER CARTRIDGE (K), and check that the lock key is in the lock position. Disconnect J314 from the CONNECTOR CRUM. Is each cable of J31 J314 continuous. Replace the TONER CARTRIDGE. Go to step 2. 2 Checking the error Replace the TONER CARTRIDGE. Does the error still occur when turning of and on the power. Go to step 2. Go to step 3. 2 Checking the printing Reload a paper to SSI. Go to step 3. End of work 3 Checking after opening and closing the COVER ASSY FRONT Open and close the COVER ASSY FRONT, and then latch correctly. Go to step 4. End of work 4 Checking the ROLL ASSY REGI and ROLL REGI METAL for shape and operation Remove the PHD ASSY once to check the followings. Are ROLL ASSY REGI and ROLL REGI METAL seated correctly. Check these items by turning with your finger. Go to step 5. Clean or replace the defective ROLL(s). 5 Checking the ROLL ASSY REGI and ROLL REGI METAL for contacting Is the ROLL REGI METAL surely contacted with the ROLL ASSY REGI by the spring force on both sides of the ROLL REGI METAL. Check this item with your finger. Are the shape and operation of the ACTUATOR SSI normal. Go to step 7. Reseat the ACTUATOR SSI. If broken or damaged, replace the ACTUATOR SSI. 7 Checking the SSI No Paper Sensor (SENSOR PHOTO) for operation Remove the CHUTE LOW (PL3.2.27) once to check the operation. Does the number on the screen increase by one, when the actuator (ACTUATOR SSI) of the SSI No Paper Sensor (SENSOR PHOTO) is operated. Replace the PWBA MCU. (Refer to REP8.11) Go to step 8. 2-36 Chapter 2 Troubleshooting 2.3 ERROR CODE FIP Step Remedy Check Yes Checking the connectors of the SENSOR PHOTO (SSI No Paper Sensor) for connection Check the connections between the PWBA MCU and SENSOR PHOTO. Go to step 10. End of work 10 Checking the HARN ASSY L SIDE for continuity Disconnect J23 from the PWBA MCU. Disconnect J233 from the SENSOR PHOTO. Is each cable of J23 J233 continuous. Go to step 11. Replace the HARN ASSY L SIDE. 11 Checking the power to the SENSOR PHOTO Disconnect J23 from the PWBA MCU. Remove the CHUTE LOW (PL3.2.27) once to check the operation. Does the voltage change, when the actuator of the SENSOR PHOTO is operated. Replace the PWBA MCU. (Refer to REP8.11) Replace the SENSOR PHOTO.(Refer to REP3.10) 2-37 Chapter 2 Troubleshooting 2.3 ERROR CODE FIP FIP-1.15 Jam at Front (MPT Insert Jam) Step Remedy Check Yes No Possible causative parts: HARNESS ASSY L SIDE (PL3.1.18) SENSOR PHOTO (PL3.2.13) PWBA MCU (PL8.2.13) 1 Checking the customer operation Did the customer insert the paper to the SSI during print. After print completion, insert Go to step 2. the paper to the SSI. 2 Checking the SSI No Paper Sensor for operation Does the number on the screen increase by one, when the actuator (ACTUATOR SSI) is operated by paper. Go to step 3. Go to step 4. 3 Checking the error Does the error still occur when printing. Go to step 6. End of work 6 Checking the HARN ASSY L SIDE for continuity Disconnect J23 from the PWBA MCU. Go to step 7. Replace the HARN ASSY L SIDE. 7 Checking the power to the SENSOR PHOTO Disconnect J23 from the PWBA MCU. Go to step 2. End of work. 2 Checking the paper setting Was the paper correctly set to Tray. Go to step 4. Set the paper correctly, and go to step 3. 3 Does the error still occur when printing. Go to step 4. End of work. 4 Checking the ROLL ASSY REGI and ROLL REGI METAL for contacting Is the ROLL REGI METAL surely contacted with the ROLL ASSY REGI by the spring force on both sides of the ROLL REGI METAL. Go to step 6. Go to step 7. 6 Checking the Regi. Sensor (SENSOR PHOTO) for operation Does the number on the screen increase by one, when the actuator (ACTUATOR REGI IN) of the Regi. Sensor (SENSOR PHOTO) is operated. Checking the connectors of the CLUTCH ASSY DRV (Regi Clutch) for connection Check the connections between the PWBA MCU and CLUTCH ASSY DRV (Regi Clutch). Disconnect P262 from the CLUTCH ASSY DRV. Is each cable of J26 P262 continuous. Go to step 9. Replace the HARN ASSY KSNR REGCL. 9 Checking the power to the CLUTCH ASSY DRV Disconnect J26 from the PWBA MCU. Is the resistance across J262-1 and J262-2 approximately 280ohm. Replace the PWBA MCU. (Refer to REP8.11) Replace the CLUTCH ASSY DRV. Disconnect J232 from the SENSOR PHOTO. Is each cable of J23 J232 continuous. Go to step 13. Replace the HARN ASSY L SIDE. 13 Checking the power to the SENSOR PHOTO Disconnect J23 from the PWBA MCU. Replace the PWBA MCU. (Refer to REP8.11) Replace the SENSOR PHOTO.(Refer to REP3.12) Checking the connectors of the SENSOR PHOTO (Regi Sensor) for connection Check the connections between the PWBA MCU and SENSOR PHOTO. Go to step 2. Go to step 4. 2 Checking the paper setting Was the paper correctly set to SSI without slant. Go to step 4. Set the paper to SSI correctly, and go to step 3. 3 Does the error still occur when printing. Go to step 4. End of work 4 Checking the paper condition Is the paper wrinkled or damaged. Replace the paper with a new and dry one, then go to step 5. Go to step 6. 5 Does the error still occur when printing. Go to step 7. End of work 6 Checking after reloading a new paper Reload a new paper. Go to step 7. End of work 7 Checking the COVER ASSY FRONT for latching Open and close the COVER ASSY FRONT, and then latch correctly. Warning: Start the operation after the FUSER ASSY has cooled down. Go to step 10. End of work 10 Checking the Exit Sensor for operation Does the number on the screen increase by one, when the actuator of the Exit Sensor in the FUSER ASSY is operated. Replace the PWBA MCU. (Refer to REP8.11) Go to step 11. 2-41 Chapter 2 Troubleshooting 2.3 ERROR CODE FIP Step Remedy Check Yes No Checking the connectors of the Exit Sensor in the FUSER ASSY for connection Check the connections between the PWBA MCU and FUSER ASSY. Disconnect J17 from the PWBA MCU. Is each cable of J17 P171 continuous. NOTE: P171 is attached to the frame. Go to step 13. Replace the HARN ASSY FUSER. 13 Checking the power to the Exit Sensor in the FUSER ASSY Disconnect the connector of J17 on the PWBA MCU. Does the voltage change, when the actuator of the Exit Sensor is operated. Replace the PWBA MCU. (Refer to REP8.11) Replace the FUSER ASSY. (Refer to REP6.1) 11 2-42 Chapter 2 Troubleshooting 2.3 ERROR CODE FIP FIP-1.18 Jam at Exit Step Remedy Check Yes No Possible causative parts: FUSER ASSY (PL6.1.1) HARNESS ASSY FUSER (PL6.1.2) PWBA MCU (PL8.2.13) 1 Checking the error Clear the jammed paper. Go to step 2. End of work. 2 Checking the paper setting Was the paper correctly set to SSI or CASSETTE1. Go to step 4. End of work. 4 Checking the FUSER ASSY installation Reseat the FUSER ASSY. Go to step 7. End of work. 7 Checking the COVER ASSY FRONT for latching Open and close the COVER ASSY FRONT, and then latch correctly. Go to step 8. End of work. 8 Checking the Exit Sensor for operation Does the number on the screen increase by one, when the actuator of the Exit Sensor in the FUSER ASSY is operated. Checking the connectors of the Exit Sensor in the FUSER ASSY for connection Check the connections between the PWBA MCU and FUSER ASSY. Go to step 11. Replace the HARN ASSY FUSER. 11 Checking the power to the Exit Sensor in the FUSER ASSY Disconnect the connector of J17 on the PWBA MCU. Go to step 3. Use the paper that meets the specifications, then go to step 2. 2 Does the error still occur when printing. Go to step 3. End of work 3 Checking the paper condition Is the paper in the SSI wrinkled or damaged. Replace the paper with a new and dry one, then go to step 4. Go to step 5. 4 Does the error still occur when printing. Go to step 6. End of work 5 Checking after reloading a new paper Reload a new paper in the SSI. Go to step 6. End of work 6 Checking the COVER ASSY FRONT for latching Open and close the COVER ASSY FRONT, and then latch correctly. Go to step 7. End of work 7 Checking the paper lead edge staying position Does the paper lead edge stay before the ROLL ASSY REGI and ROLL REGI METAL. Go to step 8. The paper lead edge stay after the ROLL ASSY REGI and ROLL REGI METAL, then go to step 13. 8 Checking after resetting the guide sides of the SSI Reset the side guides. Go to step 9. End of work 9 Checking the paper transfer path between the SSI paper loading window and Regi.Sensor Are there any obstacles on the paper transfer path. Remove the obstacles or stain from the paper transfer path, then go to step 10. Go to step 11. 10 Does the error still occur when printing. Go to step 11. End of work 11 Checking the ACTUATOR SSI for shape and operation Remove the CHUTE LOW (PL3.2.27) once to check the operation. Go to step 12. Reseat the ACTUATOR SSI. If broken or damaged, replace the ACTUATOR SSI. 2-45 Chapter 2 Troubleshooting 2.3 ERROR CODE FIP Remedy Step Check 12 Checking the SSI No Paper Sensor (SENSOR PHOTO) for operation Remove the CHUTE LOW (PL3.2.27) once to check the operation. Go to step 13. Go to step 16. 13 Checking the Regi. Does the Regi. Clutch (CLUTCH ASSY DRV) operate properly, and the ROLL ASSY REGI and ROLL REGI METAL rotate. During this check, cheat the interlock switch (HARN ASSY INTERLOCK). Go to step 14. Go to step 25. 14 Checking the ACTUATOR REGI ROLL for shape and operation Remove the CHUTE LOW (PL3.2.27) once to check the shape and operation. Are the shape and operation of the ACTUATOR REGI ROLL normal. Go to step 15. Reseat the ACTUATOR REGI ROLL. If broken or deformed, replace it with a new one. 15 Checking the Regi. Sensor (SENSOR PHOTO) for operation Does the number on the screen increase by one, when the ACTUATOR REGI ROLL is operated. Yes Checking the connectors of the SENSOR PHOTO (SSI No Paper Sensor) for connection Check the connections between the PWBA MCU and SENSOR PHOTO (SSI No Paper Sensor). Go to step 18. End of work 18 Checking the HARN ASSY L SIDE for continuity Disconnect J23 from the PWBA MCU. Go to step 19. Replace the HARN ASSY L SIDE. 19 Checking the power to the SENSOR PHOTO Disconnect J23 from the PWBA MCU. No Replace the SENSOR PHOTO.(Refer to REP3.10) Checking the connectors of the SENSOR PHOTO (Regi Sensor) for connection Check the connections between the PWBA MCU and SENSOR PHOTO. Go to step 23. Replace the HARN ASSY L SIDE. 23 Checking the power to the SENSOR PHOTO Disconnect J23 from the PWBA MCU. Does the voltage change, when the ACTUATOR REGI ROLL is operated. Replace the PWBA MCU. (Refer to REP8.11) Replace the SENSOR PHOTO.(Refer to REP3.12) 21 2-47 Chapter 2 Troubleshooting 2.3 ERROR CODE FIP Step Remedy Check Yes No Checking the connectors of the CLUTCH ASSY DRV (Regi Clutch) for connection Check the connections between the PWBA MCU and CLUTCH ASSY DRV. Go to step 27. Replace the HARN ASSY KSNR REGCL. 27 Checking the power to the CLUTCH ASSY DRV Disconnect J26 from the PWBA MCU. Go to step 3. End of work 3 Checking the paper condition Is the paper wrinkled or damaged. Go to step 6. End of work 5 Checking after reloading a new paper Reload a new paper. Remove the remaining paper. If the belt is damaged, replace the TRANSFER ASSY. (Refer to REP6.3) Go to step 10.