3m soundpro manual
LINK 1 ENTER SITE >>> Download PDF
LINK 2 ENTER SITE >>> Download PDF
File Name:3m soundpro manual.pdf
Size: 3969 KB
Type: PDF, ePub, eBook
Category: Book
Uploaded: 20 May 2019, 16:41 PM
Rating: 4.6/5 from 693 votes.
Status: AVAILABLE
Last checked: 4 Minutes ago!
In order to read or download 3m soundpro manual ebook, you need to create a FREE account.
eBook includes PDF, ePub and Kindle version
✔ Register a free 1 month Trial Account.
✔ Download as many books as you like (Personal use)
✔ Cancel the membership at any time if not satisfied.
✔ Join Over 80000 Happy Readers
3m soundpro manualAttach the calibrator and cal adapter to the SoundPro. Set the calibrator to 1 KHz and 114 dB (if it is a selectable).The chart displays measurements in each filter band and broadband values for both meters. For octave band analysis, the screen contains 13 bars (11 for filters and 2 for broadband), and for third-octave analysis the screen contains 35 bars (33 for filters and 2 for broadband) of measurement values. The 3M Detection brand of instrumentation is used by safety and industrial hygiene professionals to help comply with applicable occupational standards and regulations. The SoundPro series helps deliver the accurate sound. The amplitude of the displayed measurement is shown both graphically by the length of the bar and numerically below value is above the minimum value for the selected measurement range.It is also used for extended battery life with up to one week of continuous monitoring (two weeks with optional second battery). The weatherproof case holds the meter and battery pack with room for accessories and storage of the system components while not in use. Exposed components are made of stainless steel, ABS and engineered polymers. The OMS kit contains all necessary masts,. Rugged Comfort Half Facepiece Respirator 6500 Series 2 Pages Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates. Type 1 sound level meters are available to rent on a daily, weekly, or monthly basis. Performing area sound level surveys or perimeter monitoring studies. Add a weatherproof enclosure to protect the instrumentation from exposure to wind, rain, snow, chemicals, and particulate. It can also extend battery life for continuous monitoring for up to two weeks. The case holds the meter and battery pack, with room for accessories. Using your SoundPro for outdoor noise surveys. Get a pre-assembled outdoor noise monitoring kit, complete with enclosure and power.http://www.oma.org.tw/public_html/pics/3ym30-parts-manual.xml
- Tags:
- 3m soundpro manual, 3m sound pro user manual, 3m soundpro se dl manual, 3m soundpro sound level meter manual, 3m soundpro manual pdf, 3m soundpro manual download, 3m soundpro manual free, 3m soundpro manual instructions.
Octave band analysis enables environmental noise monitoring, noise enforcement, and noise control evaluation. Book a Service Job Instruments due for a service. Book a Service Job. Page 3 ii Table of ContentsModels and options. 1. Frequency resolution. 2Turning on. Page 5 iv Table of Contents. Setting up auto-run. 38Calibrate. 61Specifications. 125. Conformance to standards. 125Logging (optional). 133. Part numbers. 133Figure 4-3: Example of setting up. Page 12 xi Table of Contents. Figure 6-17: Curve results. 97. Figure 6-18: Measurement type selection (STIPA). 101. Figure 6-19: STI-PA. Page 13 xii Table of ContentsIntroductionPage 15 2 Frequency resolutionPage 16 3 Frequency resolutionPage 17 4 Frequency resolutionThis is explained in further detail inPage 20 7 Physical CharacteristicsPage 21 8 Information screenPage 23 10 Detection Management Software DMSGetting StartedPage 25 12 Microphone and accessoriesPage 26 13 Microphone and accessoriesPage 27 14 Providing powerPage 28 15 Providing powerPage 29 16 Providing powerPage 30 17 Providing powerPage 31 18 Turning onPage 32 19 SoundPro functionalityPage 33 20 SoundPro functionalityPage 34 21 Turning offPage 35 22 Turning offPage 37 24 Basic setupsPage 38 25 Basic setupsPage 40 27 Basic setupsPage 42 29 Basic setupsPress EnterPage 44 31 LoggingPage 45 32 LoggingA change in. Page 48 35 Setting up display optionsWith a quick.http://www.scuderieverdina.it/scuderia/userfiles/3zz-fe-manual.xml Page 49 36 Setting up display optionsPage 52 39 Setting up auto-runPage 53 40 Setting up auto-runPage 54 41 Setting up auto-runPage 55 42 Setting up auto-runPage 56 43 Setting up auto-runPage 57 44 Setting up auto-runPage 59 46 Locking setup or run modePage 60 47 Locking setup or run modePage 61 48 Locking setup or run modePage 62 49 Locking setup or run modePage 64 51 CommunicationsPage 65 52 CommunicationsPage 66 53 CommunicationsPage 68 55 CommunicationsPage 73 60 Preparing to measurePage 74 61 CalibratePage 75 62 CalibratePage 76 63 CalibratePage 79 66 Measurement navigationPage 80 67 Measurement screen iconsPage 86 73 Back-erasingPage 87 74 Back-erasingPage 89 76 Back-erasingRT60, Curves, and STI-PAPage 91 78 Additional optionsPage 92 79 Additional optionsPage 95 82 Additional optionsPage 96 83 Additional optionsPage 100 87 CurvesPage 102 89 Captured curvesPage 104 91 Criterion curve familiesPage 106 93 Criterion curve familiesPage 108 95 Audiometric background curvesPage 109 96 Running and viewing curvesThe following screens. Page 111 98 Speech IntelligibilityPage 113 100 Speech IntelligibilityPage 117 104 Speech IntelligibilityPage 119 106 Speech IntelligibilityPage 120 107 Speech IntelligibilityPage 121 108 Speech IntelligibilityViewing Past MeasurementsPage 125 112 File directoriesPage 126 113 File directoriesThe results will be played. Page 127 114 File directoriesPage 128 115 File directoriesPage 129 116 File directoriesPage 131 118 Configuration directory. Page 132 119 Configuration directoryCommunicatingPage 139 126 Appendix APage 141 128 Appendix APage 143 130 Appendix AUse for general, higher-level, free-Page 146 133 Appendix APage 149 136 Appendix APage 151 138 Appendix BPage 152 139 Appendix B. Exceedance Level (Ln). Exceedance levels represent the percent of the run time that was spent at or. Page 153 140 Appendix B. Exchange Rate of 3 dB. The display will switch to ExpHrs if RTIME is greater than 3600.http://www.drupalitalia.org/node/67426 Page 154 141 Appendix BNCB (Balanced Noise Criterion Curves ). This is the most recent incarnation of the curves based on. Page 156 143 Appendix BPage 157 144 Appendix B. Response time (F,S, I). The responseRoom Criterion. Page 159 146 Appendix B. Taktmx. A time average over a sampling interval that uses the highest level occurring during theWeighting (A, C, Z, F). SPL measurements are commonly weighted (scaled) in relation to their frequencyPage 163 150 Appendix CExpHrs Setting measurement type. 26ExpSec MeasurementsPage 166 153 IndexOverload RunSetup files(Config.) Viewing result screens. 104. This product is not intrinsically safe. Warning! Failure to observe the following procedures could damage the instrument Read the manual before operation. Do not store in temperatures exceeding 60 C (140 F). Do not immerse in liquids. Condensation may damage your instrument. Substitution of components may impair the accuracy of the instrument. Repair should be performed by authorized service personnel only. Caution! General The battery in this instrument has limited shelf-life, even if never used. A non-condensing environment is required for proper measurements. Intended Use: The SoundPro is intended to measure sound pressure levels in air. This manual explains the features and functions of all models in the series and points out distinctions between the models. CHAPTER 1 Models and options There are twelve models in the SoundPro SE and DL series. The differences between models are accounted for by three primary characteristics: accuracy of measurement, frequency resolution, and the types of data stored. The table in Figure 1-1 summarizes the characteristics of all twelve models and includes add-on features for Reverberation, Speech Intelligibility and Acoustic Spectral Curves. Some sounds, such as a whistle or a horn, have frequencies concentrated in relatively narrow regions of the audio spectrum, which ranges from approximately 20 Hz to 20,000 Hz.https://conform-edit.com/images/3m-s50-manual.pdf Other sounds, more generally thought of as noise, include components from many regions of the entire spectrum. When analyzing sound as noise, we usually are concerned with the total impact of the sound signal. In other words, we are usually satisfied with a broadband measurement of sound in the environment. When we are seeking to isolate a sound from other sounds, for instance to detect the source of a sound or to measure how much particular sounds contribute to the overall sound level, we may want to look at the frequency components of the sound. Octave bands The ability of an instrument to separate a signal into its frequency components is known as a spectral analysis. In sound pressure measurement, the audio spectrum is divided into adjacent frequency bands called octaves, where the center frequency of each octave band is twice the center frequency of the octave band directly below it. There are eleven octave bands in the audio spectrum. Figure 1-2 illustrates the relationship between the bandwidth of a typical sound measuring instrument and the octave bands that span the audio spectrum. Note that the highest and lowest octaves at 16 Hz and 16 khz lie entirely within the bandwidth of the instrument. Level Figure 1-2: Octave bands 16 3 Frequency resolution Third -octave bands Third -octave bands Each octave band can be divided into three adjacent bands called thirdoctave band. Because of the logarithmic relationship between adjacent bands, the center frequencies of third-octave bands differ from each other by 26. For example, the center frequency of the next third-octave band above the 1000 Hz third-octave band is at 1260 Hz. Figure 1-3 is similar to Figure 1-2 but shows the thirty-three third-octave bands in relation to the instrument s bandwidth. Level Figure 1-3: Third Octave bands Naming bands Bands are conventionally named for their center frequencies in accordance with acoustical industry standards. If your instrument comes equipped with a filter, it can perform an octave or a third-octave analysis, or both, depending upon the type of filter installed. You can vary the analysis type between sessions, and the analysis type selection remains constant throughout the session. In some circumstances, however, you may want to save intermediate measurement results. The SoundPro DL logging option provides you with that capability. With logging enabled, you can save selected measurements at fixed intervals during a session. You can set logging to occur as often as once per second or as seldom as once per hour. Once the logging characteristics are determined, the setup remains the same for the duration of the session. Logged data is automatically saved to the instrument s memory card and can be viewed in QSP II ( Information screen on page 8). NOTE: You must use a compatible SD card. For information about replacing the SD card, see Compatibility on page 117. Physical Characteristics The Display The transflective LCD display contains an area on the top of the screen for indicators including run, pause, stop icons and a run time clock. The middle of the screen contains a fine resolution of pixels in which data is displayed 19 6 Physical Characteristics Hardware interfaces both numerically and graphically. This is explained in further detail in Chapter 2, The Display and keypad ). Hardware interfaces The Hardware Interface Panel, shown in Figure 1-4, is located under a hinged cover in the base of the instrument. The cover can be lifted by a tab at one side, and snapped shut again by closing and pressing firmly at the center. The card should always be in place when you are operating the instrument. More information about operating with the memory card is given under Memory card on page 106. One end fits the mini B port in the instrument. The other end fits a standard USB connector on a personal computer. Users are responsible for providing their own cable. Power jack DC power can be delivered to the instrument through the Power jack. Power will be taken from the external source rather than the instrument s batteries when the external source provides 8 to 16 volts DC (300ma minimum). Two optional sources for this power are available: a switching power supply connected to an AC source and DC power provided through the accessory jack of most automobiles. The two types of functions, described below, are available through the terminals of this port. A pinout of the port is provided under Auxiliary connector on page 139. RS A group of contacts within the port supports the RS-232 protocol for communication between the instrument and other devices, such as a Global Positioning Satellite (GPS) receiver. In the Start screen, press to select Unit Info, then press. Line 2 - Unique serial number assigned when the instrument was manufactured. Line 3 The installed feature s field lists any extra options (note: these may be additionally purchased features as displayed above for Curves and STI- PA.) NOTE: It s a good idea to record Information screen data in the event that you need assistance and the instrument refuses to power up. For 3M assistance, see Contacting 3M on page 149. 22 9 Detection Management Software DMS DMS Start Page Detection Management Software DMS 3M Detection Management Software DMS is used to record, report, chart and analyze data collected for assessment of select occupational health hazards in the workplace. Designed for dosimetry, sound level measurements, heat stress assessments and environmental monitoring, the software helps safety and occupational professionals: Retrieve, download, share and save instrument data Generate insightful charts and reports Export and share recorded data Perform What If analysis and recalculate data based on selected time intervals Set up instruments and check for firmware updates Some data can only be displayed in DMS. One example is logging data obtained when logging is enabled in an instrument equipped with that option ( Logging on page 33). Another example is with the GPS function. When enabled the data is viewable in DMS. DMS Start Page Navigational buttons (1) Setup (2) Download (3) Data Finder (look at your session data or use Quick Report feature) 23 10 Detection Management Software DMS DMS Start Page This page left intentionally blank 24 11 Checking the equipment DMS Start Page Getting Started CHAPTER 2 This chapter provides the basic information you need to get up and go essentially right out of the box, including getting your first glimpses of SPL. Checking the equipment If your instrument was sent to you in a storage case, you will want to remove all the packaging and acquaint yourself with the equipment, so you can quickly get started. The items below are included in a standard SoundPro SE or DL kit. Connecting to the instrument Place the preamp connector over the mating connector at the top of the instrument. Gently press down while rotating the preamp until the preamp connector drops slightly in place. It will fit snuggly. Connecting an extension cable Extension cables are available from 3M as options and are typically used to distance the instrument body from the microphone to reduce distorting reflections from the instrument s case. 1. Attach the cable to the base as if it were the preamp and then follow the steps above Connecting to the instrument. Attach the preamp to the other end of the cable. See Distinctions between models on page 1 for information about this classification. Note that the BK4936 microphone is provided with a Random Incidence Corrector (RIC). Use the same microphone instructions for information about using and installing that device. Before using, be sure to remove the plastic cap and save it in the case for future use. Before using, be sure to remove plastic cap and save it in the case for future use. No Yes NOTE: to properly remove the microphone, please adhere to the caution sticker located on the backside of the instrument and the drawing to the right. Figure 2-3: SoundPro with microphone and windscreen 27 14 Providing power Installing Batteries Providing power You can power the instrument with internal batteries or from an external power source. Disposable alkaline batteries are satisfactory, but you may also use rechargeable Nickel Metal Hydride (NiMH) batteries. Recharge batteries externally using the recharging device available from 3M or a compatible device available elsewhere. NOTE: To avoid possible battery leakage, remove the batteries when the meter is not in use for prolonged periods. To install batteries 1. With the back of the instrument facing up, push the release latch to pop open the battery lid (Figure 2-1). Figure 2-4: Installing batteries 2. Lift off the lid and set aside. Wedge out the four batteries. 3. Replace the batteries with fresh batteries, taking care that you orient all batteries with the positive ends toward the base, as shown in the drawing. 4. Re-insert the lid by fitting its locator pins into slots in the base end of the battery compartment. When operating on batteries, the grey area in each cell graphic indicates the charge on each cell (Figure 2-5). When operating on an external power source (see next section, external power sources ), the external power will take precedence over batteries if installed. Battery indicator If all bars appear up to starting line, this indicates full battery power Externally powered If using an external power source, EXT will appear and all batteries will be fully shaded indicating full power capacity. You will be at the start screen. The Battery Check screen appears. A: Press softkey to select Alkaline B: Press softkey to select NiMH Softkey buttons Figure 2-7: Selecting battery type in battery check screen 4. Press the softkey that corresponds with the installed battery type (See A or B in Figure 2-7 for selection). If the external power source provides the correct voltage (8-16 VDC) and sufficient current (300 ma minimum), it will be used in place of the batteries if they re installed in the instrument. Auto adapter Universal power supply Figure 2-8 illustrates the assembly of the Universal power supply and the plug adapter. It slides into place by guiding it down the back cavity (opening) of the power supply. - NOTE: the example is a typical adapter which may be different than the one you are using. Mechanically, it will function similarly. A. Universal power supply 9V B. Slide plug adapter into the crevices of base Figure 2-8: Attaching the charger adapter with the plug adapter Connecting power supply source 1. Ensure the power supply is assembled (for universal power supply only). 2. Plug the power cord into the power jack by opening the base cover. Start screen and the keypad The Start screen is the first screen you see when you power on and the last screen you see when you shut down. This essential main screen is also used to navigate through the menu options. The keypad and softkeys are used to setup the instrument, run a study, stop a study, view your measurement values, and power on and off the meter. Table 2-1: Keypad Explained 33 20 SoundPro functionality Indicators explained Indicators explained Status information is provided by the instrument at the top of the display. Below is a summary of all of the indicators. Icon Significance Battery charge status. A full battery indicates one of the following: externally powered or the SoundPro is fully charged. Run state. This icon appears when a study is running. Paused state. This icon appears when the current session is open but paused. Stop state. This icon appears when the current session is stopped. Review mode. When the pause and stop icons appear, this indicates that you are viewing a saved file. OL Overload condition. When an overload occurs during a study, this indicator appears and remains lit until the beginning of the next study. UR Underrange condition. When an underrange condition occurs during a study, this indicator appears and remains lit until the beginning of the next study. Alternate functions. This icon appears below the Battery Charge Indicator when alternate functions are being displayed. If you press ESC repeatedly, you will return to the start screen. The following table displays the required microphone settings. Input, then press Enter. Polarization field - Polarization remains highlighted. Then do one of the following: a. For Time field, press Enter repeatedly to highlight either the hour, minutes, or seconds. This is assessable at all times unless you are running a study. To change or set the measurement type, ensure the SoundPro is stopped as indicated by the stop icon. Depending on the options you ordered with your SoundPro it may or may not have all the measurement types indicated above. NOTE: For STI-PA and RT60, please see Chapter 6, Additional Options. An underline denotes which feature is selected. 5. To set the weighting for Meter 1, press the third softkey repeatedly until either A, C, Z, of F is underlined (or selected). To set Meter 2 response time and weighting, press 4 th softkey until Meter 2 is selected. Continue to press Enter until the specified setting is selected. Press the Left arrow to return to the Meter Set fields. These are in the following SoundPro screens: Measures Set screen, View Current Study screen, and View Session study screen. Measurement setup (for community noise) The measure screen is used to select community noise settings for meter 1 only. Table 3-2 below explains the settings and options. Setting up community noise measurements (refer to figure 3-5 below) 1. Ensure you are at the start screen. Measurements L1-L4 LDN, CNEL Lc-a, TAKTMX 1 2 Data fields Edit column 1 or column 2 fields by pressing enter repeatedly to toggle through selections. Figure 3-5: Measures screen for community noise settings 5. To make changes to the data fields, do one of the following: L1-L4 - Press Enter to move to the data field. In the data field, repeatedly press Enter to change your selection. Press arrows to change percentage. L c-a Press Enter to select data field. The following table explains your selections in the Measures screen (Please see Appendix B, Glossary of Terms for more details.) Measurements Explanation L1-L4 (Exceedance) LDN CNEL L c-a TAKTMX L1-L4 are types of exceedance levels. This is defined as the level exceeded by the measured noise level for an identified fraction of time. Exceedance levels may be calculated for many time fractions (or percentages). Optional Settings: Set to Off or to a percentage value of your choice (1-99). Optional Settings: Set to Off or On. Community Noise Exposure Level. The accumulated exposure to sound measured in 24-hour sampling interval and artificially boosted during certain hours. This measurement (also commonly called C-A measurement) is only available under certain conditions. Information about viewing and changing these meter settings is discussed under the next section, C-A measurement settings. Optional Settings: Set to On and Off. See C-A section below for parameter settings. A time average over a sampling that uses the highest level occurring during the preceding Taktmaximal interval (either three or five seconds), and assumes it was present for the whole Taktmx interval. Optional Settings: Set to Off, 3sec, or 5sec Table 3-2: Measures screen explained 43 30 Basic setups Measurement setup (for community noise) C-A measurement settings The C-A measurement is determined from concurrent measurements of the SPL by both meters. It can only be made if certain settings for Meter 1 and Meter 2 are compatible. If you want to activate L c-a, have the following settings in place before you visit the Measures screen. Thresholds - Both meters set to Off or the same value. Exchange rates- Both meters set to the same value. Time response - Both meters set to the same value. Frequency weightings- Meter 1 must be set to A-weighting; Meter 2 must be set to C-weighting. The filter option is either a On or Off setting in Meter 1 and is only available if the instrument contains a filter option. NOTE: The filter option must be set to on to data log filtered data. Logging interval The logging interval is the length of time between logging events. NOTE: The inverse of the logging interval is the logging rate. View more Model 407780. Introduction The 407780 with programmable integrating time This device is shipped fully tested and calibrated and, Use the meter Model 42280 The 42280 is a wall-mount, tripod Model RH520 The following Installation and User Manual User s Manual. Profile For a better understanding of this product, please read this user manual thoroughly before using it. This Clamp on device allows the user to measure ground Operation Manual Please read carefully and follow all warnings and instructions in Quick Guider After getting this alarm system, you need to do the following Version: March 2016 2016 Emerson Electric Co. All rights reserved. All rights reserved. Contents MANUAL OPERATION GUIDE Buttons and Icons 3 Basic Functionality 4 Manual The Decimator ProRackG was designed to provide the maximum The best ways to achieve a cleaner, safer environment Model 407510 S2: Added MI010. S4.1: added Quick Start Guide If you have any other questions or concerns, please call 1-800-777-7899 or go to www.izzo.com. Notes Before using the product, be sure to read Lenovo Safety and General Information INDEX Page USE. 3 WARRANTY. 3 FOR SAFE USE. 4 BEFORE USE THE DETECTOR. The Tablet PC is a fully functional PC with built-in LAN, and wireless connectivity. With your Tablet PC you will be Toll Free Customer Support 1-877-269-8490 www.stealthcam.net Lightspeed Aviation is a trademark and Zulu and FRC are registered trademarks of Lightspeed Aviation, Inc. Bluetooth is a registered trademark User Manual Review the main User Guide Vroom CANBUS USER INTERFACE WITH LCD GRAPHIC DISPLAY AND WITH TEMPERATURE AND HUMIDITY SENSOR Safety Operation Maintenance Model 407730 The 0770 measures and displays sound pressure levels in db User Guide This manual will help you to get started with setting up your notebook. The final product configuration depends on the model at the point of your It takes the desired audio signal To use this website, you must agree to our Privacy Policy, including cookie policy. Updates In the interests of continuous product improvements, 3M Quest Technologies reserves the right to make changes to product speci.SoundPro User Manual. Measuring Instruments 3M SE User Manual pages. Related Manuals for 3M SoundPro SE series. Also for: Soundpro dl series. TSI Quest SoundPro DL sound level meters include two virtual sound 3m soundpro dl manual level meters for simultaneous measurements in accordance with regulatory standards. Failure to observe the following procedures may result in serious personal injury Not for use in explosive or hazardous locations. It is also used for. Measures to dB for SoundPro Class 1 meters. Failure to observe the following procedures may result in serious personal injury. The new SoundPro SE and DL Series of Hand Held Sound Level Meters and Real-Time Frequency Analyzer in combination with QuestSuite Professional II applications software is specifically designed to greatlysimplify the efforts required to reliably perform advanced noise analyses. TSI Quest (formerly 3M) SP-DL-2 SoundPro DL Class 2 Sound Level Meter Kit Includes: SoundPro DL Sound Level Meter with Summary Datalogging, Time History and Statistical Datalogging, Class 2 Microphone, Windscreen, Four Disposable AA Alkaline Batteries, Wrist Strap, Calibrator Adapter, USB Cable, SD Memory Card and Storage Case. SoundPro SE series Measuring Instruments pdf manual download. Sound Level Meters. SoundPro and downloading. This manual explains the features and functions of 3m soundpro dl manual all models in the series and points out distinctions between the models. Shipping Dimensions (LxWxD) 26x20x Weight (lbs) Power: Replaceable AA Batteries, DC Line power: Ask a Question. Let’s kick off our front panel hardware discussion with the iPad dock connector. Type 2 sound level meters are available to rent on a daily, 3m soundpro dl manual weekly, 3m soundpro dl manual or monthly basis. Worcestershire. Buy SP Dl 3m soundpro dl manual 1 1 3 SoundPro Dl Class 1 Datalogging 1 1 and 1 3 Octave RTA Summary Data and more from our comprehensive selection of 3M Quest SoundPro Sound 3m soundpro dl manual Level Meters. These hand-held instruments include two virtual sound level meters to take full or third octave band real-time. Models SE and DL 3MTM SoundPro Sound Level Meter. 3M Quest SoundPro DL meters include two virtual sound level meters for environmental sound level regulatory requirements. Sound Level Meters, Version A, microphones. The SoundPro is intended to measure sound pressure levels in air. Audiometers and audiometric testing supplies. SoundPro User Manual. Our nationwide network of labs are ISO certified and ISO accredited by A2LA. Right arrow key 5. The TSI Quest SoundPro measures workplace noise by exposure. Filter Results By. Buy 3M SP-DL-2 Soundpro Dl Class 2 Datalogging Sound Level Meter Summary Data Summary and more from our comprehensive selection of 3M Quest SoundPro Sound Level Meters. Changing time and date settings 1.